Here is a kids octagon picnic table that mimics our full size octagon picnic table. These eight-sided tables are great for kids and adults, as they allow everybody an easy access in and out. The open spaces between each seat means no kids are having to climb over each other to sit down or get up.

Materials Required

• 1 – pressure treated 1×6 deck board @ 6′
• 3 – non-pressure treated 1×6 deck boards @ 8′
• 6 – pressure treated 2×3 @ 8′
• 5 – pressure treated 2×4 @ 8′
• 1 – 1×2 @ 8′
• 3 1/2″ carriage bolts, washers and nuts
• 5″ carriage bolts, washers and nuts
• Exterior grade pocket hole screws

Tools Required

• Miter saw and circular saw
• Kreg pocket hole jig
• Drill / driver combo
• Quick clamps
• Tape measure
• Square
• Protractor
• Sander and sand paper

Step 1: Build the top

The top of this kids octagon picnic table starts with eight pieces of non-pressure treated 1×6 deck boards cut to 16″ on the long side. Each end should be cut at a 67 1/2° angle, so when the pieces are all assembled you get the outer frame of your octagon. Since you are cutting eight of these that need to be the same, I recommend gang cutting two at a time. Or you can create a jig with a stop block to ensure their uniformity. Use three pocket hole screws on the underside of each joint to hold the outer frame together.

Once the outer frame is assembled, you can move onto filling in the inside with more non-pressure treated 1×6 deck boards. You should be able to fit two boards across the center with an 1/8″ gap in between each board. Use three pocket hole screws on each end of these boards to attach them to the frame. Then continue cutting the remaining boards with 45° angles on each end to fill in the rest of the top. Also leaving a 1/8″ gap in between boards and attaching with three pocket hole screws. Note, you will have to rip cut the last board down to width.

Step 2: Add the supports for the top

Once you have the table top built for this kids octagon picnic table you’ll need to add some support beams. There are three different variations of the pieces you’ll need to cut for these 2×3 support beams:

• 1 – 38″ 2×3
• 2 – 18 1/4″ 2x3s
• 4 – 17 3/4″ 2x3s, with one end cut to form a 90° point.

All seven of the above pieces should also have one end with a 45° cut in it to remove the sharp corner. This helps to keep people from banging their knees or thighs.

Start by attaching the 38″ piece using pocket hole screws every 6-8″, alternating sides with the hole. Next attach the 18 1/4″ pieces, centered on the 38″ piece. Again, use pocket hole screws every 6-8″ alternating sides. Finally, attach the 17 3/4″ pieces in the same manner.

Step 3: Cut and attach the legs.

The four leg pieces are going to be cut from 2x3s (you could also use 2x4s if you want). These are simple cuts at 60° on each end, so each side is 21 1/2″ long. Clamp the legs in place so they are just over 3″ in from the outer end of the top support beams. Make certain the legs across from each other are on the same side of the support beam. Pre-drill two holes through each leg and corresponding support beam, then attach using the 3 1/2″ carriage bolts.

Step 4: Seat support frame

For the seat support frames you are making two almost identical assemblies. The first consists of a pressure treated 2×3 cut to 58″, plus two additional 2×3 pieces cut to 28″. The second consists of another 58″ 2×3, plus two additional 2×3 pieces cut to 26 1/8″. You can attach the shorter pieces to the respective 58″ pieces by using 3″ exterior grade wood screws going through the 58″ pieces and into the ends of the shorter pieces. Just make certain you measure appropriately prior to attaching. One 2×3 should be in from the outer end of the 58″ piece 25 3/4″, while the other should be in 27 3/4″. This should leave a 1 1/2″ gap in between the boards for the legs to go through.

Attach the seat support frame to the four legs using two 5″ carriage bolts per leg. Remember to clamp the seat support frames in place, and pre-drill the holes first.

Step 5: Leg bases and seat supports

The next step in these octagon picnic table plans is the leg bases and seat supports. You will be making four of these, so to save time you’ll want to make all four at once. The leg bases are made from the pressure treated 1×6 deck board. Each of these bases is just a 14 1/2″ piece, with the outside corners cut off at 45° angles for visual effect.

Cut the seat support posts from 2x4s with a 71° angle on each end. Attach to the outer edges of the leg base, again use 3″ exterior wood screws from underneath. These should be aligned to the inside edge of the leg base.

Step 6: Add the bench seats

The bench seats are the last pieces to assemble in this build. They are made from 2x4s with the inside angle set at 67 1/2°. Since you’ll be making four of these, each with two sets of two identical pieces, it is best to gang cut them. Once you have the seat boards cut, assemble the adjoining boards using three pocket hole screws per joint. Then using 2 1/2″ wood screws to attach the 1×2 pieces that hold the seat boards together.

Once assembled, attach to the seat support frame and seat supports using 2 1/2″ exterior wood screws. You can screw from the top of the seat down into the support boards. Note again that the seat is not centered over the support frame. The seat should actually be centered over the 2×4 support beam that runs directly under the corner joint. This will allow the seat to line up perfectly with the corner of the table.

Step 7: Sand all corners and surfaces

Now that you have your kids octagon picnic table completely built, it’s time to sand all of the corners down to have a nice rounded over edge. While you’re at it, it’s also a good idea to give the seats and the top a good once over with 120 grit sand paper. We don’t want any of our party guests getting splinters!

Once you’re done the sanding, add a coat of stain to protect your new picnic table from the elements. You’ll want this piece to last for years to come!

We hope you enjoyed these kids octagon picnic table plans. As always, if you have any questions reach out to us via the Comments section below. And if you do build something based on any of our plans, we’d love for you to share your experience and some pictures with us through our Submit Your Build page.

* This post may have affiliate links, which means I may receive commissions if you choose to purchase through links I provide (at no extra cost to you). As an Amazon Associate I earn from qualifying purchases. Thank you for supporting the work I put into this site.