These DIY X-base console table plans are a simple way to make your own rustic console table, and are easy to adjust to almost any width. This version of the X-base console table is designed to sit just about the same height as most counter tops at 33 1/2″. It’s also designed to be a good width to sit most cable boxes and components for a tv that is mounted above it.

Materials

• 1 – 2×8 at 8′
• 1 – 4×4 at 3′
• 1 – 1×4 at 4′
• 2 – 2×4 at 3′

Tools

• Saw (circular, miter, or table)
• Drill/Driver
• Sander and sandpaper
• Hammer/nail gun
• Square
• Tape measure
• Wood glue
• Wood screws
• Brad nails.

Step 1: Cut the 8 pieces for the X supports

This is probably the most complex step of the entire build because you need to make two separate miter cuts. The first miter is cut at 63.7° (26.3° from 90). The second miter is the opposite, a 26.3° angle (or 63.7° off the 90). If you’re using a table saw, you need to set your blade to the 63.7° angle and then stand your 2×4 on end to make one cut and then lay it flat to make the other. Using a miter saw is a little more complicated, as most don’t allow you to make a cut on an angle that steep – at least not safely (so I’m not going to go into that here).

Step 2: Assemble the lower X base

One of the nice things about these X-base console table plans, is that using the 1x4s in the design allows you to drive your screws up through it into the upright 2×4 and the bottoms of the X-base supports. This saves you from having to use as many pocket hole screws – which means less exposed fasteners.

Use wood glue and 2 1/2″ wood screws to first attach the 26 1/4″ upright 2×4. Ensure that this board is centered in the middle of the 1×4.

Next, again using wood glue, use 1 1/2″ wood screws to attach the bottoms of the lower X supports to the 1×4 and 2″ wood screws to secure the tops of the lower X supports to the upright 2×4. Then repeat the process with the top X supports.

Step 3: Attach the base and feet

Start by cutting your 4×4 into two 15″ pieces. The cut a 45 degree miter on the top of each end, 1 3/4″ up from the bottom and 1 3/4″ in from the edge. Cut four pieces of 1×4 at 3 1/2″ width, and attach with wood glue and brad nails to the outside bottom edges of the 4×4 to form the feet.

Once you have your bases built, use wood glue and brad nails through the 1×4 and down into the base to attach the two sections you just built.

Step 4: Attach the stretcher

Now that you have both of your leg assemblies built for this X-base console table, the next step is to attach the stretcher. The stretcher is just a 29″ piece of 2×4. Use two 5″ lag screws from the outside of each X base into the end of the stretcher to attach this piece. I recommend pre-drilling the holes for these, and also counter-sinking the heads. This also gives you the option of putting plugs over the heads to hide these screws.

Step 5: Attach the top

These X-base console table plans are designed so that you can use a single 2x8x8′ for the table top. Cut the 2×8 into two pieces each 44″ in lenght. After you cut the 2×8, there’s no need to attach the two boards to each other – simply use wood glue and screws through the 1×4 on the top of each X base to secure the top in place. Of course, you want to ensure you have the boards positioned perfectly before screwing them in. This should mean a 4″ overhang on each end, and a 1/2″ overhang on the sides.

Now that your construction is done, all you have left is to sand, paint or stain, and enjoy!

If you have comments or question, please feel free to connect with us via the comments section below or use our Contact Form. We love the feedback! Also, don’t forget to check out our other free DIY furniture plans and to share a few pics if you build something from any of our plans.

* This post may have affiliate links, which means I may receive commissions if you choose to purchase through links I provide (at no extra cost to you). As an Amazon Associate I earn from qualifying purchases. Thank you for supporting the work I put into this site.