By request, here are plans for a slightly narrower version of our popular 70″ sliding door console plans. These plans are exactly the same except the overall depth is 4″ less, making the top 15″ deep instead of 19″.  Looking for more options for sliding door consoles? Then check out one of our other sliding door console plans.

Materials:

• 2 – 2×8 at 6 feet long
• 1 – 1×8 at 6 feet long (or 2 if you want the floor to be boards instead of plywood)
• 1 – 1×6 at 6 feet long (or 2 if you want the floor to be boards instead of plywood)
• 1 – 4′ x 8′ sheet of 1/4″ thick plywood or hardboard (for back)
• 1 – 4′ x 4′ sheet of 1/2″ thick plywood (for the door)
• 3 – 1×2 @ 6 feet long
• 4 – 1×4 @ 6 feet long
• 6 – 2×3 @ 6 feet long
• 1 – 4′ x 8′ sheet of 3/4″ plywood (for the floor)
• Wood screws
• Nails
• Hardware for sliding doors – You can buy the hardware for sliding doors, or you can make your own.  I made my own for my rustic barn wood dog crate.

Tools:

• Saw: circular, miter, and/or table saw.
• Drill / Driver
• Nail Gun or hammer
• Kreg jig
• Sander and sandpaper
• Square
• Tape Measure
• Wood Glue (I’m a fan of Titebond)

Step 1: Build the upper and lower frames

Start by assembling your assembling your upper and lower frames.  These are made out of 2x3s, and are identical.  Use wood glue and 2 1/2″ wood screws for all joints.

Step 2: Add the plywood sides

Cut your two sides from the 3/4″ plywood sheet.  These are each 36″ high, by 13 1/4″ wide. Note that these will be 1/4″ wider than the frames so that you can let that 1/4″ overhang the back edge and will conceal the outer edges of the back panels we’ll add later.

I like using 16 gauge nails and wood glue. The glue itself, if applied correctly, will provide a much stronger bond than any mechanical fastener.  So the nails are really just holding it in place until the glue dries.

Note: Now is a good time to check to ensure the piece is square, before moving onto the face frame.

Step 3: Attach the face frame

The entire face frame is made out of 1 x 4 boards. My face frame rails are continuous across the entire top, with the stiles being attached either biscuits, pocket screws, or mortise and tenon joinery.  Just remember, if you plan on using mortise and tenon joinery, you are going to have to cut your boards longer than the measurements shown in the diagram below.

Step 4: Console floor and shelf

My sliding door console plans use a 13 x 67″ piece of 3/4″ plywood for the bottom shelf.  Wood glue and a few finish nails can hold this in place.

The four 14″ vertical shelf supports, made from 1x2s, are glued and attached to the backs of the face frame.  The two outer ones should be pushed flush to the cabinet sides, while the two middle ones are centered on the face frame boards.

The shelf in these sliding door console plans consists of a 1×8 and a 1×6 both cut to 67″ in length and then held together by four 13″ horizontal shelf supports made from 1x2s.  When building, make certain the horizontal shelf supports are aligned over the vertical supports installed on the last step. The shelf should be resting on the horizontal supports, not the shelf boards.

Once the shelf is in place in the cabinet, attach the outer horizontal shelf supports to the cabinet sides using 1 1/4″ wood screws or nails.

• 

• 

• 

Step 5: Rip and attach plywood back planking

When you are ready to install the back planking, you have two options:

1. Make all of the planks the exact same, which means cutting eleven boards at 6 3/32″, or
2. Make the boards varying widths for a more rustic/reclaimed look.

In either case, you will install them the same.  Use wood glue and nails (or staples) at the top and bottom of each board to attach to the frames, and also secure the middle of the planks to the middle shelf to provide more structural integrity to the entire piece.

Note: it’s also a good practice to ensure the back of the piece is still square before you start attaching the planks.

Step 6: Bottom Trim

The bottom trim is made of 1×2 stock, cut with 45 degree miters.  Simply glue and nail it on.

Step 7: Console Top

The next step is attaching the top.  This consists of the two 2×8 boards, cut down to 70″.   Align them flush with the back of the piece, and overhanging each side by 3/4″.   To hide the fasteners, use a Kreg jig and pocket screws from underneath going through the upper frame.  Alternatively, you could use 4″ wood screws going straight up through the upper frame as well.  For the second method, I definitely recommend pre-drilling the holes and even countersinking them to better hide the screw heads.

Step 8: Door and sliders

The simplest way to build the door is to start by cutting a 22×30″ piece of 1/2″ plywood, and then laying 1 or 1 1/2″ strips around the edges and in an X pattern.  Though how you build the door is really what will add your custom touch to this piece, so feel free to experiment.  Just remember to keep it at 22×30″.

After you have your door built, you just need to attach it to your barn door sliders and your console is ready for finishing.  Again, you can buy the hardware for sliding doors, or you can make your own.  I really enjoy making my own because it definitively gives a more rustic or antique feel to the piece.

If you have comments or question, please feel free to connect with us via the comments section below or use our Contact Form.  We love the feedback!  Also, don’t forget to check out our other free DIY furniture plans.

* This post may have affiliate links, which means I may receive commissions if you choose to purchase through links I provide (at no extra cost to you). As an Amazon Associate I earn from qualifying purchases. Thank you for supporting the work I put into this site.