If you work with rough lumber but do not own a dedicated jointer, a well-made table saw jointing jig can be a serious shop upgrade. These jigs give you a safe, repeatable way to create that first straight reference edge so the rest of your milling goes much more smoothly. Some are ultra-simple fence add-ons, others are full sled-style builds with clamps and stops, and a few cleverly pull double duty as tapering jigs too.

Below, I gathered 10 free DIY table saw jointing jig plans and tutorials from a wide mix of makers and woodworking publishers. Whether you want the fastest possible shop-made solution or a more refined jig you will keep for years, there is a build here worth studying.

1. Jointing on the Table Saw — WoodWorkers Guild of America

Overview: This is a clean, practical build for an L-shaped jig that clamps directly to your rip fence and creates the offset needed to mimic a jointer’s infeed/outfeed relationship. The tutorial walks through construction, blade alignment, offset setup, and test cuts, which makes it especially useful for woodworkers who want to understand not just how to build the jig, but how to tune it for reliable results.

Why it is great: It is one of the clearest step-by-step explanations for turning a simple fence-mounted jig into a dependable edge-jointing setup.

Link to original plans: https://www.wwgoa.com/post/jointing-on-the-table-saw

2. Straight-Edge Cutting Jig — WOOD Magazine

Overview: WOOD Magazine’s approach uses a long plywood carrier with clamps to hold a ragged-edge board steady while the jig rides the fence. It is a smart solution for woodworkers who regularly break down rough stock and want something uncomplicated, effective, and easy to size for their own shop. The included diagram also makes this one especially easy to replicate from scraps.

Why it is great: This is a classic no-fuss design that feels approachable for beginners but useful enough for experienced builders too.

Link to original plans: https://www.woodmagazine.com/woodworking-plans/tablesaw/straight-edge-cutting-jig

3. Table Saw Jointing Jig — Bobek.net

Overview: Joseph Bobek’s jig is compact, smartly detailed, and easy to adapt. Built around a plywood base with a thicker guide edge and removable clamping fingers, it is sized for 1-inch stock but intentionally designed so you can adjust it later. The sketch and short write-up make this a great option for woodworkers who prefer straightforward shop solutions over overbuilt fixtures.

Why it is great: It delivers a very usable sled-style jointing jig with minimal parts and very little complexity.

Link to original plans: https://www.bobek.net/joe/woodworking/jointing-jig/

4. How to Cut Rough Edge Board — Woodworker’s Journal

Overview: This tutorial focuses on taming rough or crooked lumber with a reusable straight-line jig made from a thin hardboard base, a fence strip, and toggle clamps. It is more of a practical shop article than a formal dimensioned plan, but it gives enough build guidance to make your own quickly and size it to the kind of lumber you usually mill. For live-edge or mildly twisted boards, this one feels especially relevant.

Why it is great: It blends real-world lumber prep advice with a jig design that is simple, proven, and easy to customize.

Link to original plans: https://www.woodworkersjournal.com/how-to-cut-straight-edge-rough-board/

5. 5 EASY Ways to Joint Boards Without a Jointer — 731 Woodworks

Overview: Matt Outlaw includes several no-jointer methods here, but the standout for this roundup is his dedicated table saw jointing jig built with the MatchFit clamping system. It is designed to secure the board firmly, create repeatable straight cuts, and even serve as a tapering jig or high fence when needed. If you like versatile shop jigs that earn their storage space, this one is easy to appreciate.

Why it is great: It gives you a multi-use jig concept instead of a one-task shop accessory.

Link to original plans: https://www.731woodworks.com/731-blog/jointing

6. Table Saw Jointer DIY — The Prodigal Carpenter

Overview: This build leans toward the practical, shop-tested end of the spectrum. The jig uses a squared oak guide board with a plywood extension and a pair of hold-down clamps to capture the workpiece securely. The article is brief, but it gives the essential concept, the build idea, and the setup logic in a way that feels very accessible for woodworkers who like to reverse-engineer a jig from a few clear photos.

Why it is great: It is a refreshingly direct build that shows how little material it takes to make a useful jointing sled.

Link to original plans: https://theprodigalcarpenter.net/blogs/sawdust-sermons-and-prodigal-ponderings/table-saw-jointer-diy

7. Easy Tapering and Jointing Jig for the Table Saw — Woodbrew

Overview: Dylan Strachan’s design is a sleek modern take on the classic taper-and-straight-line jig. The build uses slots, hardware, and an adjustable fence arrangement so the jig can handle both angled cuts and straightening duties. That dual-purpose approach makes it a strong choice for furniture makers who routinely cut tapers but also want a reliable way to establish a clean reference edge on rough stock.

Why it is great: It combines clean design with everyday usefulness, which is exactly what a good shop jig should do.

Link to original plans: https://www.woodbrew.tv/blog/easy-tapering-and-jointing-jig-for-the-table-saw

8. Woodworking Project: Finished my Table Saw Jointer Jig — My Desultory Blog

Overview: This is a nice example of a jig built to solve a specific shop problem: straightening longer boards without a dedicated jointer. The author starts with an 8-foot piece of plywood, adds a miter-slot runner and long-reach hold-downs, and ends up with a jig tailored for milling lumber that would feel awkward on smaller sleds. That longer format makes this entry stand out from many compact versions.

Why it is great: It is one of the better options here for woodworkers who regularly handle long boards and want more support through the cut.

Link to original plans: https://mydesultoryblog.com/2024/04/woodworking-project-finished-my-table-saw-jointer-jig/

9. DIY Table Saw Taper Jig — AllFlavor Workshop

Overview: Lukas at AllFlavor Workshop presents an adjustable taper jig with step-by-step photos, downloadable plans, and a clear explanation of how the same setup can be used to straighten live-edge boards. That makes it a particularly useful inclusion for readers who like projects with a more polished tutorial structure and who appreciate a jig that crosses over between furniture work and stock prep.

Why it is great: It is detailed, beginner-friendly, and especially appealing if you want both photos and downloadable plans in one place.

Link to original plans: https://allflavorworkshop.com/table-saw-taper-jig/

10. Making a Table Saw Tapering Jig — IBUILDIT.CA

Overview: John Heisz’s version is a more robust tapering jig that can also handle straight-edge work on rough lumber, and the page includes a free downloadable plan. The stepped clamp arrangement, wide body, and generous support make it feel more substantial than the bare-bones versions, which is excellent for woodworkers who prefer a jig with a little more stability and repeatability built in from the start.

Why it is great: It offers a more refined build plus a free plan, which is a great combination for anyone who likes to build once and use a jig for years.

Link to original plans: https://ibuildit.ca/projects/table-saw-tapering-jig/

A good table saw jointing jig does not need to be complicated to be useful. In fact, one of the most encouraging things about this roundup is how many excellent versions are made from plywood scraps, a few clamps, and thoughtful setup. Some woodworkers will prefer the simplicity of a straight-line carrier board, while others will want a more adjustable taper-and-jointing hybrid they can keep close at hand for furniture work.

The best choice comes down to the kind of stock you mill most often. If you regularly work with long, rough boards, a longer sled-style jig will feel more secure. If you mostly need to true furniture parts or add the occasional taper, a dual-purpose jig may be the smarter build. Either way, these free plans prove that you do not need a dedicated jointer to get clean, glue-ready edges in a small shop.

Want more woodworking tips, tool reviews, and project plans? Subscribe to FamousArtisan.com and never miss an update!

Don’t forget to show off your work in our Share Your Build section. We truly appreciate it when people share their work and let us know how our plans turned out for others.

* This post may have affiliate links, which means I may receive commissions if you choose to purchase through links I provide (at no extra cost to you). As an Amazon Associate I earn from qualifying purchases. Thank you for supporting the work I put into this site.